- 您现在的位置：买卖IC网 > Sheet目录340 > MAX16821CATI+T (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 28-TQFN
High-Power Synchronous HBLED
Drivers with Rapid Current Pulsing
Current-Error Amplifier
The MAX16821A/MAX16821B/MAX16821C include a
transconductance current-error amplifier with a typical
g m of 550μS and 320μA output sink and source capa-
bility. The current-error amplifier output (CLP) is con-
nected to the inverting input of the PWM comparator.
CLP is also externally accessible to provide frequency
compensation for the inner current regulation loop
(Figure 2). Compensate CEA so the inductor current
negative slope, which becomes the positive slope to
the inverting input of the PWM comparator, is less than
the slope of the internally generated voltage ramp (see
the Compensation section). In applications without syn-
chronous rectification, the LED driver can be turned off
and on instantaneously by shorting or opening the CLP
to ground.
PWM Comparator and R-S Flip-Flop
An internal PWM comparator sets the duty cycle by
comparing the output of the current-error amplifier to a
2V P-P ramp signal. At the start of each clock cycle, an
R-S flip-flop resets and the high-side driver (DH) turns
on if MODE is connected to SGND, and DL turns on if
MODE is connected to V CC . The comparator sets the
flip-flop as soon as the ramp signal exceeds the CLP
voltage, thus terminating the ON cycle. See Figure 3.
Differential Amplifier
The differential amplifier (DIFF) allows LED current sens-
ing (Figure 2). It provides true-differential LED current
sensing, and amplifies the sense voltage by a factor of 1
(MAX16821A), 6 (MAX16821B), and 20 (MAX16821C),
while rejecting common-mode voltage errors. The VEA
provides the difference between the differential amplifier
output (DIFF) and the desired LED current-sense volt-
age. The differential amplifier has a bandwidth of 1.7MHz
(MAX16821A), 1.6MHz (MAX16821B), and 550kHz
(MAX16821C). The difference between SENSE+ and
SENSE- is regulated to +0.6V (MAX16821A), +0.1V
(MAX16821B), or +0.03V (MAX16821C).
60mV
PEAK-CURRENT
COMPARATOR
CLP
CSP
A V = 34.5
CSN
g m = 550 μ S
IN
PWM
COMPARATOR
MODE = GND
BST
RAMP
S
Q
DH
LX
V DD
CLK
R
Q
DL
PGND
SHDN
Figure 3. MAX16821A/MAX16821B/MAX16821C Phase Circuit
______________________________________________________________________________________
11
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX16822AASA/V+
IC LED DRIVER HIGH BRIGHT 8SOIC
MAX16826ATJ+C24
IC LED DVR HB PROGR 32-HQFN
MAX16835ATE+T
IC LED DRIVR HIGH BRIGHT 16-TQFN
MAX16838AUP+
IC LED DRIVR HIGH BRIGHT 20TSSOP
MAX1698EUB
IC LED DRVR WT/CLR BCKLGT 10MSOP
MAX17014EVKIT+
KIT EVAL FOR MAX17014
MAX17061AETI+T
IC LED DRVR WHITE BCKLGT 28-TQFN
MAX17061ETI+T
IC LED DRVR WHITE BCKLGT 28-TQFN
相关代理商/技术参数
MAX16821EVKIT+
制造商:Maxim Integrated Products 功能描述:HIGH-POWER SYNCHRONOUS HBLED DRIVER - Boxed Product (Development Kits)
MAX16822AASA/V+
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822AASA/V+T
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822AASA+
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822AASA+T
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822BASA+
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822BASA+T
功能描述:LED照明驱动器 2MHz HB w/MOSFET & HSide Crnt Sense RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX16822BEVKIT+
功能描述:LED 照明开发工具 MAX16822B Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: